Top 10 Best arduino motor driver in 2026

Main highlights

• •This is a commonly used DC motor drive module, using a small current 293 chip DC motor driver chip.
• •Using this chip you can use DC motors and power supplies of up to 10 Volts, that some pretty big motors and the chip can supply a maximum current of 600mA per channel.
• •Tested compatible for Arduino Mega, Diecimila & Duemilanove.
• •2 interface for 5V Servo connected to the Arduino's high-resolution dedicated timer - no jitter.
• •Multi-function, easy to operate, a strong driver library support and feature updates.

Main highlights

• •DROK DC motor driver input voltage range is DC 6.5V-27V, can be input DC 12V or 24V, rated output current of each port is 7A, total output power is 160W.
• •STRONG DRIVE: the motor controller board adopts dual H bridge, can drive two DC motors at the same time.
• •FORWARD and REVSERSELY ROTATE: the IN1, IN2/IN3, IN4 port can control forward or reverse motor rotation.
• •PWM SPEED CONTROL: enable signal terminal (ENA) input PWM can regulate speed, PWM frequency range 0-10KHZ.
• •UNDER VOLTAGE PROTECTION: the motor driver module is with under voltage protection to prevent instantaneous large current from damaging the module.

Main highlights

• •L298N as main driver chip makes strong driving ability/small heating/strong anti-interference/low calorific value
• •Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability
• •Dual-channel H-bridge driver working mode creates higher working efficiency
• •To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage
• •Large capacity filter capacitance, afterflow protection diode, more stable and reliable

Main highlights

• •Input voltage: 2.7 V – 10.8 V
• •Single H-bridge output current: 1.5A, can drive 2 DC geared motors.
• •Built-in overcurrent protection, short circuit protection, undervoltage lockout and overheating protection. With low power sleep mode.
• •Uses: It can drive DC motors below 1.5A and 4-wire stepper motors.
• •Replaces TB6612FNG

Main highlights

• •6.5V to 45V operating voltages
• •565-mΩ typical RDS (open) (HS+LS)
• •3.6-A peak current drive
• •Pulse-width modulation control interface
• •Current regulation without sense resistors

Main highlights

• •Using L298N made by ST company as the control chip,the module has such characteristics as strong driving ability,low calorific value and strong anti-interference ability.
• •This module can use built-in 78M05 for electric work via a driving power supply part.But to avoid the damage of the voltage stabilizing chip,please use an external 5V logic supply when using more than 12V driving voltage.
• •Using large capacity filter capacitor,this module can follow current to protect diodes,and improve the reliability.
• •Dual-channel H-bridge driver working mode creates higher working efficiency
• •To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage

Main highlights

• •L298N Motor Driver Controller Board Module: L298N as main chip. Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors
• •Operating mode: H-bridge driver (dual)
• •Logic voltage: 5V(current 0mA-36mA)
• •Drive voltage: 5V-35V(current: 2A (MAX single bridge)
• •Maximum power: 25W

Main highlights

Main highlights

• •Using the BTS7960 chip
• •Compatible with 43A high current drive capability, it can meet the driving requirements of various types of smart car motors and provide sufficient power
• •Compatible with PWM speed regulation can control the speed of the motor
• •Compatible with Forward and reverse control, can control the direction of the motor
• •Compatible with With over-current protection, short-circuit protection, over-temperature protection and other functions