Top 10 Best vesc in 2026

Main highlights

• •75100is an ESC controller, which can be used for electric skateboards/scooters/electric bicycles/robots/DIY off-road vehicles/combat off-road vehicles, etc.
• •The ESC is the Benjamin ESC series. Please use the VESC TOOL tool to adjust the parameters before use. The factory version firmware is 5.02. If you need other versions, please go to the VESC tool software (Firmware) and select the corresponding version. The version cannot be used incorrectly. Different firmwares may cause differences in parameters; otherwise, it may easily cause damage to the ESC parameters.
• •PLS note:Except for Apple computers, other computer firmware can be downloaded from our official website. Apple computers can only be purchased on Apple.Please strictly refer to the instructions and wiring diagram to ensure the safe use of the product.
• •When you just connect the controller, pay attention. If the versions are inconsistent, the page will pop up. If they are inconsistent, you need to change them to be consistent before adjusting the parameters.
• •Voltage range: 14-84V (safe within 4-20S). Do not exceed the voltage range, which may cause the ESC to burn out.
• •Continuous current: 100A; You can refer to the video. If you still don’t understand, you can contact us to send relevant videos.
• •Please connect according to the wiring diagram, and pay special attention to 3.3V and 5V. Do not short-circuit. Note: When using any throttle handle, under ADC control, make sure that the positive pole of the power supply is connected to 3.3V, not 5V.
• •FS75100*1pcs;USB cable*1pcs;Hall sensor adapter (6pins)*1pcs;Manual*1pcs.
• •Please turn off the phase filter function and choose "false" in vesc_tool when use firmware version on or above 5.3 (VESC_TOOL 3.01). Without turning off the phase filter will result in esc damage. Please do not restore the default parameters when using the wizard interface.
• •Warm reminder: The ESC seat is easy to fall off, please do not be too violent when using it.The battery and motor ports must be welded firmly

Main highlights

• •Hardware Version:ODESC V4.2
• •Drive motor:Brushless DC motor (BLDC)
• •Braking method:Power resistors, battery recycling
• •Working voltage:8-24V, 8-56V
• •Maximum current:120A Continuous current:70A
• •Top Service: If there are any question or need help , just feel free contact us , we will always here help you out within 24 hours.

Main highlights

• •More Control Modes:Support four control modes: Current/Dutycycle/Speed /Position control mode.
• •Upgrade Performance:Latest Version Firmware,support rich control interface and sensors,programmable
• •Safer & Protection functions: low voltage protection, high voltage protection, over-current protection, temperature abnormally protection, mosfets over-temperature protection.
• •Widely applications:e-skateboard,ebike,scooter,robot etc
• •Flipsky quality produce and good service for you

Main highlights

• •75200 pro v2.0 is an ESC controller, which can be used for electric skateboards/scooters/electric bicycles/robots/DIY off-road vehicles/combat off-road vehicles, etc.
• •The ESC is the Benjamin ESC series. Please use the VESC TOOL tool to adjust the parameters before use. The factory version firmware is 6.02. If you need other versions, please go to the VESC tool software (Firmware) and select the corresponding version. The version cannot be used incorrectly. Different firmwares may cause differences in parameters; otherwise, it may easily cause damage to the ESC parameters.
• •PLS note:Except for Apple computers, other computer firmware can be downloaded from our official website. Apple computers can only be purchased on Apple.Please strictly refer to the instructions and wiring diagram to ensure the safe use of the product.
• •When you just connect the controller, pay attention. If the versions are inconsistent, the page will pop up. If they are inconsistent, you need to change them to be consistent before adjusting the parameters.
• •Voltage range: 14-84V (safe within 4-20S). Do not exceed the voltage range, which may cause the ESC to burn out.Continuous current:50v/200A: 75V/150A(Values depend on the mounting,abbient temperature and air/water circulation around the device!)
• •Continuous current: 50V/200A; 75V/150A (the duration depends on the external heat dissipation); the current at the motor and bus battery end cannot exceed 200A.
• •BEC: 5V@1A, 5V output current, the receiver cannot exceed 1A.Instant current: 400A (just a moment),With relative filtering.
• •Please connect according to the wiring diagram, and pay special attention to 3.3V and 5V. Do not short-circuit. Note: When using any throttle handle, under ADC control, make sure that the positive pole of the power supply is connected to 3.3V, not 5V.
• •Warm reminder: The ESC seat is easy to fall off, please do not be too violent when using it.The battery and motor ports must be welded firmly
• •You can refer to the video. If you still don’t understand, you can contact us to send relevant videos.

Main highlights

• •Voltage: 14-84V (safe for 4S-20S);Continuous Current: 100A / Single; 200A / Dual (values depend on the mounting and ambient temperature around the device!)
• •Adopting CPU AT32F403ARCT7 with the structure of ARM Cortex-M4 allows CPU clock speed.
• •Programmable via Flipsky ESC Tool to be compatible with multi-types of motor, different battery voltages and many control ways.
• •Programmable via Flipsky remote controller VX4 (remote firmware version: VX4_V1.2.1 or above).
• •Protection functions: low and high voltage protection, over-current protection, temperature abnormally protection, mosfets over-temperature and over current protection, battery over discharge protecting, motor over-temperature protection.
• •Integrated smart switch function: supports sliding poweron and automatic shutdown function; automatic shutdown time is adjustable via ESC TOOL.
• •Supporting extra interface like front lights, rear brake lights and horn fixtures.

Main highlights

Main highlights

• •75100 Pro Size: L103mm*W58mm*H27.7mm
• •Support BLDC square wave mode control and FOC sine wave mode
• •Programmable：Based on VESC, programmable via vesc_tool with overheat and overcurrent protection.
• •More powerful :Voltage:14-84V (4-20S) ，Max Current:120A,ERPM:150000 .Provide your electric skateboard with more powerful power and a more exciting modification experience.
• •Widely applications:e-skateboard,ebike,scooter,robot etc
• •Please be careful to limit the Absolute Maximum Current below 250A,setting page
• •Top Service: If there are any question or need help , just feel free contact us , we will always here help you out within 24 hours.

Main highlights

• •Comparing with standard FSESC4.12,we made some changesin hardware design.1.Replacecapacitorwhichadopts imported capacitor with better per formanceverifiedbyV6
• •Change to use 6PSC authentic power MOSFET(MODEL:NTMFS5C628NL),imported from USA,that are used in FSESC6.6 with reliable quality
• •Change to use widely Mini USB port,<p>Small Size for wide used,can be installed various products for smaller size and lighter weight
• •It is a highly modifiable electronic speed controller designed with DIY Electric Skateboards conversions in mind.
• •Plication areas:Electric Skateboard Longboard Scooter DIY Skateboard ,E-Bike,EScooter

Main highlights

• •Dual ESC can reach 100A big current, give your board strong power
• •One PCBA board integrate two FSESC4.20 ’s function by internal CAN BUS circuit connection.
• •The mater and slave board connection can be switched On/Off
• •Delicate design in details for high quality assurance: add Anti-vibration silicon pad for screw heatsink and heat-transfer pad
• •Super small size and light weight with heatsink: 79mm*65mm*19mm(L*W*H), wight: 150g